Women's Board Meeting Burgundy Business Blazer Dress
We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel.
Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth.
Construction notes
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.
The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | burgundy |
| Lining | unlined with faced seams |
| Closure | covered button placket |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 300 pcs per style |
Where this style fails in production
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.
Options on the table
- Vent, back seam, or plain back.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Private label: woven label, care label and hangtag to your artwork.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.