Welcome to Bafinasa official website!

Structured Blazer Office Dress Wholesale

Source:News / Time:2026-11-14

This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. A Structured Blazer Office Dress Wholesale reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.

Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.

The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. We keep the lapel as its own pattern piece so it can be changed without re-cutting the body.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

The sheet we need before costing

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningfully lined, bagged hem
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ50 pcs sample order

Where this style fails in production

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

Customisation that does not break the price

  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Vent, back seam, or plain back.
  • Single or double breasted front, without re-cutting the back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Private label: woven label, care label and hangtag to your artwork.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top