Welcome to Bafinasa official website!

Charcoal Grey Trench Blazer Office Dress for Office

Source:News / Time:2026-11-14

Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in grey, the inside is structure, and the two have to agree on the same sample. Most of the money in a Charcoal Grey Trench Blazer Office Dress for Office sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening.

Structure and seams

The build follows the same order on every size. These are the steps where the shape is won or lost. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.

We keep the lapel as its own pattern piece so it can be changed without re-cutting the body. The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygrey
Lininghalf lined to the hip
Closurecovered button placket
Size runS-XL (4 sizes) for the test
Sample lead time12-18 days after spec sign-off
MOQ150 pcs per style

What to check before bulk

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end.

Changes we can make at sample stage

  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Vent, back seam, or plain back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Single or double breasted front, without re-cutting the back.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top