Welcome to Bafinasa official website!

Emerald Green Tailored Blazer Office Dress for Office Work

Source:News / Time:2026-11-14

Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back.

Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.

The tailored is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. If the tailored is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygreen
Liningfully lined, bagged hem
Closureconcealed side zip
Size run34-44 with a regional grade
Sample lead time15-20 days with handwork
MOQ50 pcs sample order

The places this usually goes wrong

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end.

Changes we can make at sample stage

  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Vent, back seam, or plain back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Private label: woven label, care label and hangtag to your artwork.
  • Private label: woven label, care label and hangtag to your artwork.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top