Board Meeting Emerald Green Double Breasted Blazer Office Dress
The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Board Meeting Emerald Green Double Breasted Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in green, the inside is structure, and the two have to agree on the same sample. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.
Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet.
Structure and seams
Most of the handwork sits in a handful of steps, and each one has a right order. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.
The double breasted is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. If the double breasted is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Shoulder and neckline decide whether a Board Meeting Emerald Green Double Breasted Blazer Office Dress looks expensive. Both are set by the block, not by the sewing. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates.
What goes on the spec sheet
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | green |
| Lining | half lined to the hip |
| Closure | invisible centre-back zip |
| Size run | 34-44 with a regional grade |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 50 pcs sample order |
The places this usually goes wrong
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered.
What we can change for you
- Vent, back seam, or plain back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Single or double breasted front, without re-cutting the back.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.