Office Work Burgundy 2 Piece Blazer Office Dress Set
There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. A Office Work Burgundy 2 Piece Blazer Office Dress Set reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together.
Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.
Where the shape comes from
Most of the handwork sits in a handful of steps, and each one has a right order. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.
The lapel reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.
What goes on the spec sheet
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | burgundy |
| Lining | bodice lined, skirt lined |
| Closure | covered button placket |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 150 pcs per style |
Failure points worth designing out
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing.
Options on the table
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Vent, back seam, or plain back.
- Single or double breasted front, without re-cutting the back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.