Welcome to Bafinasa official website!

Office Work Wrap Blazer Office Dress

Source:News / Time:2026-11-14

A Office Work Wrap Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Most of the money in a Office Work Wrap Blazer Office Dress sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. Written down, the request is office work wrap blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press.

Construction notes

The build follows the same order on every size. These are the steps where the shape is won or lost. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

When the brief names the wrap, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. We keep the wrap as its own pattern piece so it can be changed without re-cutting the body.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

The sheet we need before costing

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningunlined with faced seams
Closurecovered button placket
Size runXS-2XL plus a curve block
Sample lead time10-14 days on stock cloth
MOQ300 pcs per style

What to check before bulk

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder.

What we can change for you

  • Single or double breasted front, without re-cutting the back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Vent, back seam, or plain back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top