Welcome to Bafinasa official website!

Board Meeting Navy Blue Business Blazer Dress

Source:News / Time:2026-11-14

Written down, the request is board meeting navy blue business blazer dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in navy, the inside is structure, and the two have to agree on the same sample.

We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.

Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The lapel reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Shoulder and neckline decide whether a Board Meeting Navy Blue Business Blazer Dress looks expensive. Both are set by the block, not by the sewing. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel.

The sheet we need before costing

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaynavy
Liningunlined with faced seams
Closureinvisible centre-back zip
Size run34-44 with a regional grade
Sample lead time15-20 days with handwork
MOQ100 pcs per colour

The places this usually goes wrong

  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.

Options on the table

  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Vent, back seam, or plain back.
  • Single or double breasted front, without re-cutting the back.
  • Private label: woven label, care label and hangtag to your artwork.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top