Welcome to Bafinasa official website!

Board Meeting Emerald Green Blazer Office Dress

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in green, the inside is structure, and the two have to agree on the same sample. A Board Meeting Emerald Green Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.

Where the shape comes from

The build follows the same order on every size. These are the steps where the shape is won or lost. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.

If the lapel is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. The lapel reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

Shoulder and neckline decide whether a Board Meeting Emerald Green Blazer Office Dress looks expensive. Both are set by the block, not by the sewing. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygreen
Liningbodice lined, skirt lined
Closureconcealed side zip
Size run34-44 with a regional grade
Sample lead time15-20 days with handwork
MOQ100 pcs per colour

Failure points worth designing out

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder.

Options on the table

  • Single or double breasted front, without re-cutting the back.
  • Vent, back seam, or plain back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top