Welcome to Bafinasa official website!

Women's Office Work Camel 2 Piece Blazer Office Dress Set

Source:News / Time:2026-11-14

This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.

Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.

The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. The lapel reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaycamel
Liningunlined with faced seams
Closureinvisible centre-back zip
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ300 pcs per style

Where this style fails in production

  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.

What we can change for you

  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Vent, back seam, or plain back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Private label: woven label, care label and hangtag to your artwork.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top