Welcome to Bafinasa official website!

Burgundy Pleated Blazer Office Dress for Office Work

Source:News / Time:2026-11-14

A Burgundy Pleated Blazer Office Dress for Office Work reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Written down, the request is burgundy pleated blazer office dress for office work: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting.

Structure and seams

The build follows the same order on every size. These are the steps where the shape is won or lost. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.

The pleated is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. Check the pleated after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

The sheet we need before costing

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwayburgundy
Liningunlined with faced seams
Closureconcealed side zip
Size run34-44 with a regional grade
Sample lead time12-18 days after spec sign-off
MOQ300 pcs per style

What to check before bulk

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing.

Options on the table

  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Vent, back seam, or plain back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Private label: woven label, care label and hangtag to your artwork.
  • Private label: woven label, care label and hangtag to your artwork.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top