Welcome to Bafinasa official website!

Light Grey Career Blazer Office Dress

Source:News / Time:2026-11-14

Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in grey, the inside is structure, and the two have to agree on the same sample. Most of the money in a Light Grey Career Blazer Office Dress sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing.

Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.

Structure and seams

Most of the handwork sits in a handful of steps, and each one has a right order. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.

The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. If the lapel is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygrey
Lininghalf lined to the hip
Closurecovered button placket
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ300 pcs per style

The places this usually goes wrong

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

What we can change for you

  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Vent, back seam, or plain back.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Private label: woven label, care label and hangtag to your artwork.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top