Welcome to Bafinasa official website!

Office Work Burgundy A-line Blazer Office Dress

Source:News / Time:2026-11-14

Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. A Office Work Burgundy A-line Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Most of the money in a Office Work Burgundy A-line Blazer Office Dress sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount.

Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.

Where the shape comes from

The build follows the same order on every size. These are the steps where the shape is won or lost. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.

We keep the lapel as its own pattern piece so it can be changed without re-cutting the body. The lapel reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwayburgundy
Liningunlined with faced seams
Closureinvisible centre-back zip
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ150 pcs per style

The places this usually goes wrong

  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder.

What we can change for you

  • Vent, back seam, or plain back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Single or double breasted front, without re-cutting the back.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top