Welcome to Bafinasa official website!

Office Work Emerald Green 2 Piece Blazer Office Dress Set

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Office Work Emerald Green 2 Piece Blazer Office Dress Set reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Written down, the request is office work emerald green 2 piece blazer office dress set: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

How it is built

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. Shoulder and neckline decide whether a Office Work Emerald Green 2 Piece Blazer Office Dress Set looks expensive. Both are set by the block, not by the sewing.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygreen
Liningfully lined, bagged hem
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time15-20 days with handwork
MOQ300 pcs per style

The places this usually goes wrong

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

What we can change for you

  • Vent, back seam, or plain back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Single or double breasted front, without re-cutting the back.
  • Private label: woven label, care label and hangtag to your artwork.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top