Burgundy Tailored Blazer Office Dress for Office Work
It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in burgundy, the inside is structure, and the two have to agree on the same sample. Most of the money in a Burgundy Tailored Blazer Office Dress for Office Work sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. Written down, the request is burgundy tailored blazer office dress for office work: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel.
We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.
How it is built
Most of the handwork sits in a handful of steps, and each one has a right order. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.
Check the tailored after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. When the brief names the tailored, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Shoulder and neckline decide whether a Burgundy Tailored Blazer Office Dress for Office Work looks expensive. Both are set by the block, not by the sewing.
Specification, item by item
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | burgundy |
| Lining | unlined with faced seams |
| Closure | stretch panel, no zip |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 50 pcs sample order |
Where this style fails in production
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
Changes we can make at sample stage
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Vent, back seam, or plain back.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Single or double breasted front, without re-cutting the back.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.