Welcome to Bafinasa official website!

Board Meeting Navy Blue Pleated Blazer Office Dress

Source:News / Time:2026-11-14

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Written down, the request is board meeting navy blue pleated blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press.

Where the shape comes from

The build follows the same order on every size. These are the steps where the shape is won or lost. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.

The pleated reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. The pleated is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaynavy
Liningunlined with faced seams
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time10-14 days on stock cloth
MOQ300 pcs per style

The places this usually goes wrong

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.

Options on the table

  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Single or double breasted front, without re-cutting the back.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top