Welcome to Bafinasa official website!

Burgundy Peak Lapel Blazer Office Dress for Office Work

Source:News / Time:2026-11-14

It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in burgundy, the inside is structure, and the two have to agree on the same sample. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. Written down, the request is burgundy peak lapel blazer office dress for office work: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form.

How it is built

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

We keep the lapel as its own pattern piece so it can be changed without re-cutting the body. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

What goes on the spec sheet

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwayburgundy
Lininghalf lined to the hip
Closureconcealed side zip
Size runS-XL (4 sizes) for the test
Sample lead time10-14 days on stock cloth
MOQ100 pcs per colour

Failure points worth designing out

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Options on the table

  • Vent, back seam, or plain back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Single or double breasted front, without re-cutting the back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top