Women's Office Work Camel Double Breasted Blazer Office Dress
A Women's Office Work Camel Double Breasted Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. A Women's Office Work Camel Double Breasted Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together.
Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.
How it is built
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.
The double breasted is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. If the double breasted is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.
Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
What goes on the spec sheet
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | camel |
| Lining | unlined with faced seams |
| Closure | covered button placket |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 15-20 days with handwork |
| MOQ | 100 pcs per colour |
The places this usually goes wrong
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
Changes we can make at sample stage
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Vent, back seam, or plain back.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Private label: woven label, care label and hangtag to your artwork.
Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
