Office Work Emerald Green Double Breasted Blazer Office Dress
A Office Work Emerald Green Double Breasted Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. A Office Work Emerald Green Double Breasted Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.
Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening.
How it is built
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.
When the brief names the double breasted, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. If the double breasted is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.
On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Shoulder and neckline decide whether a Office Work Emerald Green Double Breasted Blazer Office Dress looks expensive. Both are set by the block, not by the sewing. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.
Specification, item by item
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | green |
| Lining | fully lined, bagged hem |
| Closure | stretch panel, no zip |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 50 pcs sample order |
Failure points worth designing out
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing.
What we can change for you
- Vent, back seam, or plain back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Single or double breasted front, without re-cutting the back.
- Private label: woven label, care label and hangtag to your artwork.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
