Office Work White Double Breasted Blazer Office Dress
There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Office Work White Double Breasted Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Written down, the request is office work white double breasted blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.
Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.
Construction notes
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.
If the double breasted is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. We keep the double breasted as its own pattern piece so it can be changed without re-cutting the body.
Shoulder and neckline decide whether a Office Work White Double Breasted Blazer Office Dress looks expensive. Both are set by the block, not by the sewing. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.
What goes on the spec sheet
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | white |
| Lining | fully lined, bagged hem |
| Closure | concealed side zip |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 50 pcs sample order |
Where this style fails in production
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
What we can change for you
- Single or double breasted front, without re-cutting the back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Private label: woven label, care label and hangtag to your artwork.
The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
