Office Work Charcoal Grey Long Sleeve Blazer Office Dress
Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Written down, the request is office work charcoal grey long sleeve blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back.
Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.
Construction notes
The build follows the same order on every size. These are the steps where the shape is won or lost. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.
The long sleeve reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. When the brief names the long sleeve, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
Shoulder and neckline decide whether a Office Work Charcoal Grey Long Sleeve Blazer Office Dress looks expensive. Both are set by the block, not by the sewing. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | grey |
| Lining | unlined with faced seams |
| Closure | covered button placket |
| Size run | 34-44 with a regional grade |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 300 pcs per style |
What to check before bulk
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.
Customisation that does not break the price
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Vent, back seam, or plain back.
- Single or double breasted front, without re-cutting the back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.
Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
