Office Work Double Breasted Blazer Office Dress for Work
Written down, the request is office work double breasted blazer office dress for work: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. A Office Work Double Breasted Blazer Office Dress for Work reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together.
Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening.
Where the shape comes from
Most of the handwork sits in a handful of steps, and each one has a right order. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.
We keep the double breasted as its own pattern piece so it can be changed without re-cutting the body. When the brief names the double breasted, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel.
The sheet we need before costing
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | half lined to the hip |
| Closure | concealed side zip |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 15-20 days with handwork |
| MOQ | 150 pcs per style |
The places this usually goes wrong
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.
Customisation that does not break the price
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Single or double breasted front, without re-cutting the back.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
