Business Professional Burgundy 2 Piece Blazer Office Dress Set
The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Most of the money in a Business Professional Burgundy 2 Piece Blazer Office Dress Set sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel.
Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.
Where the shape comes from
Most of the handwork sits in a handful of steps, and each one has a right order. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.
The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Shoulder and neckline decide whether a Business Professional Burgundy 2 Piece Blazer Office Dress Set looks expensive. Both are set by the block, not by the sewing. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.
The sheet we need before costing
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | burgundy |
| Lining | bodice lined, skirt lined |
| Closure | concealed side zip |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 12-18 days after spec sign-off |
| MOQ | 150 pcs per style |
The places this usually goes wrong
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder.
What we can change for you
- Vent, back seam, or plain back.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
