Office Work Camel Double Breasted Blazer Office Dress
Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Written down, the request is office work camel double breasted blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back.
Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.
Construction notes
Most of the handwork sits in a handful of steps, and each one has a right order. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.
The double breasted is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. The double breasted reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.
Specification, item by item
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | camel |
| Lining | bodice lined, skirt lined |
| Closure | covered button placket |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 15-20 days with handwork |
| MOQ | 100 pcs per colour |
The places this usually goes wrong
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.
Customisation that does not break the price
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Vent, back seam, or plain back.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
