Women's Office Work Charcoal Grey Long Sleeve Blazer Office Dress
It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in grey, the inside is structure, and the two have to agree on the same sample. A Women's Office Work Charcoal Grey Long Sleeve Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Most of the money in a Women's Office Work Charcoal Grey Long Sleeve Blazer Office Dress sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.
Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.
How it is built
The build follows the same order on every size. These are the steps where the shape is won or lost. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.
Check the long sleeve after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The long sleeve is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. Shoulder and neckline decide whether a Women's Office Work Charcoal Grey Long Sleeve Blazer Office Dress looks expensive. Both are set by the block, not by the sewing.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | grey |
| Lining | fully lined, bagged hem |
| Closure | invisible centre-back zip |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 150 pcs per style |
The places this usually goes wrong
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder.
Changes we can make at sample stage
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Single or double breasted front, without re-cutting the back.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Vent, back seam, or plain back.
- Private label: woven label, care label and hangtag to your artwork.
- Private label: woven label, care label and hangtag to your artwork.
The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.
