Welcome to Bafinasa official website!

Classic Tailored Office Blazer Dress

Source:News / Time:2026-11-14

A Classic Tailored Office Blazer Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte, the inside is structure, and the two have to agree on the same sample. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Most of the money in a Classic Tailored Office Blazer Dress sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing.

Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.

The tailored is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. Check the tailored after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates.

The sheet we need before costing

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningfully lined, bagged hem
Closurecovered button placket
Size run34-44 with a regional grade
Sample lead time15-20 days with handwork
MOQ300 pcs per style

Where this style fails in production

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

Customisation that does not break the price

  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Vent, back seam, or plain back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top