Welcome to Bafinasa official website!

Women's Office Work White Tailored Blazer Office Dress

Source:News / Time:2026-11-14

Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Women's Office Work White Tailored Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in white, the inside is structure, and the two have to agree on the same sample.

The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.

Construction notes

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

The tailored is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. If the tailored is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. Shoulder and neckline decide whether a Women's Office Work White Tailored Blazer Office Dress looks expensive. Both are set by the block, not by the sewing.

What goes on the spec sheet

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaywhite
Liningbodice lined, skirt lined
Closureconcealed side zip
Size runS-XL (4 sizes) for the test
Sample lead time15-20 days with handwork
MOQ300 pcs per style

What to check before bulk

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

What we can change for you

  • Vent, back seam, or plain back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Single or double breasted front, without re-cutting the back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top