Classic Tailored Midi Blazer Office Dress
A Classic Tailored Midi Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte, the inside is structure, and the two have to agree on the same sample. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.
Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening.
Construction notes
The build follows the same order on every size. These are the steps where the shape is won or lost. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.
If the tailored is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. When the brief names the tailored, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
What goes on the spec sheet
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | midi |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | half lined to the hip |
| Closure | covered button placket |
| Size run | 34-44 with a regional grade |
| Sample lead time | 15-20 days with handwork |
| MOQ | 150 pcs per style |
What to check before bulk
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder.
What we can change for you
- Vent, back seam, or plain back.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.