Welcome to Bafinasa official website!

Women's Office Work Black 2 Piece Blazer Office Dress Set

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.

The lapel reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwayblack
Liningunlined with faced seams
Closurecovered button placket
Size runS-XL (4 sizes) for the test
Sample lead time12-18 days after spec sign-off
MOQ300 pcs per style

Failure points worth designing out

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

What we can change for you

  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Single or double breasted front, without re-cutting the back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top