Welcome to Bafinasa official website!

Charcoal Grey Corporate Blazer Dress for Office Work

Source:News / Time:2026-11-14

Most of the money in a Charcoal Grey Corporate Blazer Dress for Office Work sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting.

Where the shape comes from

Most of the handwork sits in a handful of steps, and each one has a right order. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Shoulder and neckline decide whether a Charcoal Grey Corporate Blazer Dress for Office Work looks expensive. Both are set by the block, not by the sewing.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygrey
Lininghalf lined to the hip
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ300 pcs per style

What to check before bulk

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.

Customisation that does not break the price

  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Single or double breasted front, without re-cutting the back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Vent, back seam, or plain back.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top