Welcome to Bafinasa official website!

Office Work Camel Blazer Office Dress

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in camel, the inside is structure, and the two have to agree on the same sample. A Office Work Camel Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet.

Where the shape comes from

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

If the lapel is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Shoulder and neckline decide whether a Office Work Camel Blazer Office Dress looks expensive. Both are set by the block, not by the sewing.

What goes on the spec sheet

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaycamel
Liningunlined with faced seams
Closureinvisible centre-back zip
Size runXS-2XL plus a curve block
Sample lead time10-14 days on stock cloth
MOQ300 pcs per style

Failure points worth designing out

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.

Options on the table

  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Vent, back seam, or plain back.
  • Single or double breasted front, without re-cutting the back.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top