Buy Business Professional Navy Blue Notch Lapel Blazer Office Dress
We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in navy, the inside is structure, and the two have to agree on the same sample.
Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.
Where the shape comes from
Most of the handwork sits in a handful of steps, and each one has a right order. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.
If the lapel is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | navy |
| Lining | fully lined, bagged hem |
| Closure | invisible centre-back zip |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 300 pcs per style |
Where this style fails in production
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.
Customisation that does not break the price
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Single or double breasted front, without re-cutting the back.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.
A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.