Emerald Green Business Professional Double Breasted Blazer Office Dress
Written down, the request is emerald green business professional double breasted blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Emerald Green Business Professional Double Breasted Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together.
Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet.
How it is built
Most of the handwork sits in a handful of steps, and each one has a right order. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.
The double breasted reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. The double breasted is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
Specification, item by item
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | green |
| Lining | fully lined, bagged hem |
| Closure | concealed side zip |
| Size run | 34-44 with a regional grade |
| Sample lead time | 15-20 days with handwork |
| MOQ | 300 pcs per style |
What to check before bulk
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end.
Options on the table
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Vent, back seam, or plain back.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Single or double breasted front, without re-cutting the back.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Private label: woven label, care label and hangtag to your artwork.
The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.