Old Money Wrap Blazer Office Dress
There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. A Old Money Wrap Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together.
Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.
How it is built
Most of the handwork sits in a handful of steps, and each one has a right order. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.
We keep the wrap as its own pattern piece so it can be changed without re-cutting the body. The wrap is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.
The sheet we need before costing
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | unlined with faced seams |
| Closure | covered button placket |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 15-20 days with handwork |
| MOQ | 150 pcs per style |
Failure points worth designing out
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing.
Changes we can make at sample stage
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Single or double breasted front, without re-cutting the back.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Vent, back seam, or plain back.
- Private label: woven label, care label and hangtag to your artwork.
- Private label: woven label, care label and hangtag to your artwork.
The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.
Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.