Old Money Blazer Office Dress
There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Old Money Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Written down, the request is old money blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.
Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.
Where the shape comes from
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.
We keep the lapel as its own pattern piece so it can be changed without re-cutting the body. If the lapel is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.
Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel.
The sheet we need before costing
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | half lined to the hip |
| Closure | invisible centre-back zip |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 15-20 days with handwork |
| MOQ | 50 pcs sample order |
The places this usually goes wrong
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.
Options on the table
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Vent, back seam, or plain back.
- Single or double breasted front, without re-cutting the back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Private label: woven label, care label and hangtag to your artwork.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.
A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.