Welcome to Bafinasa official website!

Old Money Double Breasted Blazer Office Dress

Source:News / Time:2026-11-14

A Old Money Double Breasted Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Most of the money in a Old Money Double Breasted Blazer Office Dress sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing.

Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.

The double breasted reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure. Check the double breasted after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Shoulder and neckline decide whether a Old Money Double Breasted Blazer Office Dress looks expensive. Both are set by the block, not by the sewing. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningunlined with faced seams
Closurestretch panel, no zip
Size runS-XL (4 sizes) for the test
Sample lead time10-14 days on stock cloth
MOQ150 pcs per style

The places this usually goes wrong

  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

Changes we can make at sample stage

  • Vent, back seam, or plain back.
  • Single or double breasted front, without re-cutting the back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top