Charcoal Grey Business Professional Single Breasted Blazer Office Dress
The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. A Charcoal Grey Business Professional Single Breasted Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in grey, the inside is structure, and the two have to agree on the same sample. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.
Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.
Structure and seams
Most of the handwork sits in a handful of steps, and each one has a right order. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.
If the single breasted is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. Check the single breasted after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make.
What goes on the spec sheet
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | grey |
| Lining | fully lined, bagged hem |
| Closure | invisible centre-back zip |
| Size run | 34-44 with a regional grade |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 150 pcs per style |
The places this usually goes wrong
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order.
Changes we can make at sample stage
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Single or double breasted front, without re-cutting the back.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
- Private label: woven label, care label and hangtag to your artwork.
The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.