Executive Style Wrap Blazer Office Dress
We see this style in two versions. One is built to hit a price, the other to keep its shape for three seasons. They differ by about fifteen percent in cost and by a great deal in what comes back. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte, the inside is structure, and the two have to agree on the same sample.
Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks.
How it is built
The build follows the same order on every size. These are the steps where the shape is won or lost. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.
The wrap is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. When the brief names the wrap, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | fully lined, bagged hem |
| Closure | covered button placket |
| Size run | 34-44 with a regional grade |
| Sample lead time | 15-20 days with handwork |
| MOQ | 300 pcs per style |
Failure points worth designing out
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder.
What we can change for you
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Vent, back seam, or plain back.
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
- Private label: woven label, care label and hangtag to your artwork.
The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.
Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.