Welcome to Bafinasa official website!

Navy Blue Business Professional Single Breasted Blazer Office Dress

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Written down, the request is navy blue business professional single breasted blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. A Navy Blue Business Professional Single Breasted Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

Construction notes

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season.

When the brief names the single breasted, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. We keep the single breasted as its own pattern piece so it can be changed without re-cutting the body.

A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

The sheet we need before costing

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaynavy
Liningfully lined, bagged hem
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time10-14 days on stock cloth
MOQ50 pcs sample order

Where this style fails in production

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered.

What we can change for you

  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Single or double breasted front, without re-cutting the back.
  • Vent, back seam, or plain back.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Private label: woven label, care label and hangtag to your artwork.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top