Welcome to Bafinasa official website!

Women's Office Work Emerald Green Formal Blazer Office Dress

Source:News / Time:2026-11-14

It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in green, the inside is structure, and the two have to agree on the same sample. A Women's Office Work Emerald Green Formal Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. Most of the money in a Women's Office Work Emerald Green Formal Blazer Office Dress sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

Structure and seams

The build follows the same order on every size. These are the steps where the shape is won or lost. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.

When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. If the lapel is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygreen
Liningfully lined, bagged hem
Closurecovered button placket
Size runS-XL (4 sizes) for the test
Sample lead time15-20 days with handwork
MOQ150 pcs per style

Failure points worth designing out

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end.

Customisation that does not break the price

  • Vent, back seam, or plain back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Single or double breasted front, without re-cutting the back.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top