Welcome to Bafinasa official website!

Business Professional Black Double Breasted Blazer Office Dress

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. A Business Professional Black Double Breasted Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Written down, the request is business professional black double breasted blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills.

How it is built

The build follows the same order on every size. These are the steps where the shape is won or lost. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks.

We keep the double breasted as its own pattern piece so it can be changed without re-cutting the body. The double breasted is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

The sheet we need before costing

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwayblack
Liningbodice lined, skirt lined
Closurestretch panel, no zip
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ100 pcs per colour

The places this usually goes wrong

  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.

Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered.

Changes we can make at sample stage

  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Single or double breasted front, without re-cutting the back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top