Welcome to Bafinasa official website!

Executive Style 2 Piece Blazer Office Dress Set

Source:News / Time:2026-11-14

Most of the money in a Executive Style 2 Piece Blazer Office Dress Set sits in three places: the cloth, the front panel, and the labour that keeps the waist seam flat after pressing. Written down, the request is executive style 2 piece blazer office dress set: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.

Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.

If the lapel is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. The lapel reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Lininghalf lined to the hip
Closurecovered button placket
Size runS-XL (4 sizes) for the test
Sample lead time10-14 days on stock cloth
MOQ150 pcs per style

What to check before bulk

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

Customisation that does not break the price

  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Vent, back seam, or plain back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Single or double breasted front, without re-cutting the back.
  • Private label: woven label, care label and hangtag to your artwork.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top