Welcome to Bafinasa official website!

Buy Business Professional White Double Breasted Blazer Office Dress

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. A Buy Business Professional White Double Breasted Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. A Buy Business Professional White Double Breasted Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together.

Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet.

Structure and seams

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

When the brief names the double breasted, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. The double breasted is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates.

What goes on the spec sheet

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaywhite
Liningbodice lined, skirt lined
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time15-20 days with handwork
MOQ150 pcs per style

The places this usually goes wrong

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

Options on the table

  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Single or double breasted front, without re-cutting the back.
  • Vent, back seam, or plain back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Private label: woven label, care label and hangtag to your artwork.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top