Welcome to Bafinasa official website!

Women's Office Work Charcoal Grey Business Blazer Dress

Source:News / Time:2026-11-14

It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in grey, the inside is structure, and the two have to agree on the same sample. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel.

Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth.

Structure and seams

Most of the handwork sits in a handful of steps, and each one has a right order. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.

If the lapel is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. The lapel reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.

We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.

Specification, item by item

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygrey
Lininghalf lined to the hip
Closurecovered button placket
Size run34-44 with a regional grade
Sample lead time15-20 days with handwork
MOQ150 pcs per style

The places this usually goes wrong

  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth.

Changes we can make at sample stage

  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Single or double breasted front, without re-cutting the back.
  • Vent, back seam, or plain back.
  • Private label: woven label, care label and hangtag to your artwork.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top