Buy Business Professional Burgundy Midi Blazer Office Dress
A Buy Business Professional Burgundy Midi Blazer Office Dress reads as a short brief until the pattern is cut, and the shape only holds when the front panel, the waist seam and the hem allowance are settled together. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Written down, the request is buy business professional burgundy midi blazer office dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.
We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Cloth decides more than the brief admits. The same block in a 180 gsm wool blend and a 260 gsm double knit produces two different garments, one for the office and one for the evening. Request a shrink test on the actual dye lot. Half a percent across a midi is visible to the customer and invisible on the sheet.
How it is built
Most of the handwork sits in a handful of steps, and each one has a right order. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.
The lapel is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.
If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.
Spec sheet, line by line
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | midi |
| Colourway | burgundy |
| Lining | bodice lined, skirt lined |
| Closure | invisible centre-back zip |
| Size run | XS-2XL plus a curve block |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 50 pcs sample order |
What to check before bulk
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.
Customisation that does not break the price
- Vent, back seam, or plain back.
- Shoulder: soft pad, structured pad, or none with a clean finish.
- Single or double breasted front, without re-cutting the back.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Private label: woven label, care label and hangtag to your artwork.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.
Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.