Welcome to Bafinasa official website!

Emerald Green Business Professional Work Blazer Dress

Source:News / Time:2026-11-14

It helps to separate what the customer sees from what the factory feels. The outside is wool blend or ponte in green, the inside is structure, and the two have to agree on the same sample. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. Buyers arrive with a reference photo and a target price. The two numbers that decide whether that price is reachable are the cloth weight and how many seams run through the front panel.

Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

How it is built

The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line.

Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. We keep the lapel as its own pattern piece so it can be changed without re-cutting the body.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

The sheet we need before costing

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaygreen
Lininghalf lined to the hip
Closureconcealed side zip
Size runXS-2XL plus a curve block
Sample lead time10-14 days on stock cloth
MOQ100 pcs per colour

Where this style fails in production

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.

Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered.

Changes we can make at sample stage

  • Vent, back seam, or plain back.
  • Single or double breasted front, without re-cutting the back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top