Welcome to Bafinasa official website!

Business Professional Camel Double Breasted Blazer Office Dress

Source:News / Time:2026-11-14

This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered.

The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet.

Where the shape comes from

Most of the handwork sits in a handful of steps, and each one has a right order. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Pockets are cut on the straight grain and bar-tacked at the corners. A pocket that sags pulls the whole front out of line. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.

We keep the double breasted as its own pattern piece so it can be changed without re-cutting the body. If the double breasted is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.

If the buyer sells online, photograph the size chart on real bodies. That reduces returns more than any pattern change we can make. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the front panel to move at different rates.

The sheet we need before costing

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaycamel
Liningfully lined, bagged hem
Closureconcealed side zip
Size runS-XL (4 sizes) for the test
Sample lead time12-18 days after spec sign-off
MOQ150 pcs per style

Failure points worth designing out

  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Lining cut to the same length as the shell, so the dress climbs when worn.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

Options on the table

  • Single or double breasted front, without re-cutting the back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Vent, back seam, or plain back.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.

Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top