Welcome to Bafinasa official website!

Power Dressing Notch Lapel Blazer Office Dress

Source:News / Time:2026-11-14

This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes. Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. We start with wool blend or ponte on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch.

Construction notes

Most of the handwork sits in a handful of steps, and each one has a right order. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen.

We keep the lapel as its own pattern piece so it can be changed without re-cutting the body. When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping.

Spec sheet, line by line

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwaybuyer colourway, lab-dipped under two lights
Liningfully lined, bagged hem
Closurestretch panel, no zip
Size runS-XL (4 sizes) for the test
Sample lead time15-20 days with handwork
MOQ300 pcs per style

Where this style fails in production

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.

Schedule an in-line check after the front panel goes on. Catching a rotation there costs minutes; catching it at final costs the order. Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

What we can change for you

  • Vent, back seam, or plain back.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Single or double breasted front, without re-cutting the back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top