Executive Style Tailored Blazer Office Dress
This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. A Executive Style Tailored Blazer Office Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows.
Request a shrink test on the actual dye lot. Half a percent across a long hem is visible to the customer and invisible on the sheet. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Keep one dye lot for bulk. Splitting a thousand pieces across two lots is how a reorder ends up with a visible line between sizes.
How it is built
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. The vent, where there is one, is taped and pressed so it stays closed in the bag and opens when the wearer walks. The lining is joined at the armhole by hand or with a clean machine finish. A bagged lining that pulls is a return waiting to happen. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent.
Check the tailored after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. If the tailored is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the front panel. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.
Specification, item by item
| Shell | a mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk |
| Body | blazer dress |
| Length | confirmed on the wearer, in her shoes |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | half lined to the hip |
| Closure | covered button placket |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 15-20 days with handwork |
| MOQ | 300 pcs per style |
Where this style fails in production
- Lining cut to the same length as the shell, so the dress climbs when worn.
- Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
- Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
- The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment.
Customisation that does not break the price
- Lining to match or contrast. Contrast adds a visible detail at the cuff.
- Single or double breasted front, without re-cutting the back.
- Vent, back seam, or plain back.
- Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Private label: woven label, care label and hangtag to your artwork.
The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.