Welcome to Bafinasa official website!

Burgundy Pencil Blazer Office Dress Working Women

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one.

Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. For wool blend or ponte, order five to eight percent extra. Cutting around a shade band costs more than the cloth. Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Under 200 gsm, plan to interface the front panel. Without it, the seam ridge shows through at the first press.

Where the shape comes from

Most of the handwork sits in a handful of steps, and each one has a right order. Buttonholes on a blazer dress carry load. Back them with a strip of interfacing or they tear inside a season. Shoulder pads go in before the lining, and the sleeve head is eased rather than pleated. That is the difference between a clean shoulder and a dent. The front needs a canvassed or well-fused panel. A soft front under a structured shoulder collapses within two wears.

When the brief names the lapel, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. Check the lapel after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

For Blazer Office Dresses sold across regions, keep one measurement sheet per market; one market's Large is another market's Medium. A size run that stops at XL will not sell where the middle size is a Large. State the run and the grade rule at quoting, not at shipping. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

The sheet we need before costing

Shella mid-weight wool blend or a firm ponte, swatch-approved, one dye lot for bulk
Bodyblazer dress
Lengthconfirmed on the wearer, in her shoes
Colourwayburgundy
Liningunlined with faced seams
Closureinvisible centre-back zip
Size runS-XL (4 sizes) for the test
Sample lead time15-20 days with handwork
MOQ300 pcs per style

Failure points worth designing out

  • Sleeve head pleated instead of eased, giving a pucker that cannot be pressed out.
  • Front panel fused too hot, so the cloth shines and the lapel edge shows a ridge.
  • Buttons placed by eye rather than from the pattern, so the front gapes between sizes.
  • A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. In bulk the failures cluster: skipped stitches on the front panel, shading between panels, and hems that go wavy after pressing.

Options on the table

  • Vent, back seam, or plain back.
  • Sleeve length: full, three-quarter, or sleeveless with a faced armhole.
  • Shoulder: soft pad, structured pad, or none with a clean finish.
  • Lining to match or contrast. Contrast adds a visible detail at the cuff.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money.

A sample order of fifty to a hundred pieces is enough to test the pattern, the cloth and the trims before a season is committed. Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top